Datasat RS20i Specifications Page 98
- Page / 140
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
RS20i Installation and Operating Guide Page 98
RS20i Installation & Operating Guide Document # 9301H52900 Ver. 1.01
Configuration with no subwoofers:
10. Tap on Center speaker to select one of the following options for the center speaker:
a. Large– (default) select this option if you want LFE channel mixed with the center
channel.
b. Small – Select small if you do not want LFE channel mixed with the center speaker. A
high pass is also inserted for the center channel. Select the frequency and slope for the
center speaker high pass, or disable the high pass filter.
c. Low Pass to Left/Right. Send the Low portion of the center channel to the left and right
front speakers.
d. Phantom Center. Use this if there is no center speaker installed. This divides the center
channel between the left and right speakers. The offset can be adjusted.
11. Return to the Bass Management Setup screen and tap on Left or Right speaker. This selects the
speaker option for both left and right front speakers:
a. Large– (default) select this option if you want LFE channel mixed in with the left and
right channels.
b. Small – Select small if you do not want to mix LFE channel with the left and right
channels. A high pass is also inserted for the left and right channels. Select the
frequency and slope for the left and right channel high pass, or disable the high pass
filter.
12. Return to the Bass Management Setup screen and tap on Left Surround or Right Surround
speaker to select the speaker option for both left and right surround speakers.
a. Large– (default) select this option if you want LFE channel mixed in with the left
surround and right surround channels.
b. Small – Select this if you do not want to mix LFE channel with the left surround and
right surround channels. A high pass is also inserted for the surround channels. Select
the frequency and slope for the surround channel high pass, or disable the high pass filter.
c. Phantom Surround. Use this if there are no surround speakers installed. When selected
the left surround channel is mixed with the left speaker and the right surround is mixed
with the right front speaker. The offset level can be adjusted.
13. Skip this step if there are no rear surround speakers installed.
Return to the Bass Management Setup screen and tap on Rear Surround Left or Rear Surround
Right speaker. This selects the speaker option for both Rear Surround Left and Rear Surround
Right speakers:
a. Large– (default) select this option if you want LFE channel mixed in with the Rear
Surround Left and Rear Surround Right channels.
b. Small – Select this if you do not want to mix LFE channel with the Rear Surround Left
and Rear Surround Right channels. A high pass is also inserted for the rear surround
channels. Select the frequency and slope for the rear surround channel high pass, or
disable the high pass filter.
14. Return to the Bass Management Setup screen and verify the configuration. All speaker
configuration options are described in text next to the
speaker. This com
pletes the bass
management setup.
4.3.8.6.2. Bass Management Setup Screen
The figure below shows the
main bass management screen.
- RS20i Audio Processor 1
- Installation and 1
- Operating Guide 1
- Notices 2
- Copyright 2
- Record of Changes 3
- Regulatory Notices 3
- TABLEOFCONTENTS 4
- 3. APPENDICES 6
- Introduction 7
- About RS20i Audio Processor 8
- Limited Warranty 8
- FACTORY WARRANTY INFORMATION 9
- Software License Agreement 9
- Unpacking 11
- Caution Notices 12
- Part 1: Operation 13
- 1.0 Operating RS20i 14
- 2Update 15
- 258 for more details 15
- Navigating through the Menus 17
- 1.4 The Home Screen 18
- 1.4.3 Manual Automation 21
- PROBLEM SOLUTION 22
- 1.5.1 Over Temperature Alert 23
- 2.0 Installation and Set Up 26
- 2.3 Installation Overview 28
- 2.5 Mounting and Connection 30
- 2.5.4 Power Supply 32
- 2.6 Navigating the Menus 33
- 2.7 About Inputs 34
- Output preset: 35
- 2.8 Factory Presets 36
- 2.8.2 Default EQ 37
- 2.8.3 Default Output Presets 37
- 2.9.1 Equipment Requirements 38
- 2.10.2 Set the EQ 44
- 2.13 Final Adjustments 48
- 2.14 Copy Input 48
- 4.0 Setup Menus 51
- 4.1 The Setup Button 56
- 4.2 System Setup Screen 56
- 4.2.3 Access Control 60
- Figure 36. “Expert” Nav Mode 62
- 4.2.4 View Log File 63
- 4.2.5 System Info 63
- 4.2.7 System Monitor 64
- 4.3 Inputs 65
- 4.3.2 Startup Input 66
- 4.3.3 Edit Inputs 66
- 4.3.4 Assign Input Buttons 67
- 4.3.5 Input Source 69
- 4.3.6 Input Options 71
- Operation 78
- Decoder Setup Options 78
- 4.3.7 EQ Setup 79
- Figure 62. Copy EQ Settings 84
- 4.3.8 Output Preset 86
- 4.3.9 Audio Levels 104
- 4.4 Network 106
- 4.5 Automation 111
- 4.5.1 Events 112
- 4.5.2 Macros 117
- 4.5.3 Automation Buttons 118
- 4.5.4 Automation Test Screen 119
- 5.1 Routine Maintenance 120
- 5.2 Troubleshooting 120
- Touch Screen Calibration 121
- 5.3 Error Messages 122
- Figure 98. Downloading Error 123
- HDMI 1.4a Dolby/DTS Decoder 136
- Digital Audio Decoders 137
- Signal Inputs 137
- Signal Outputs 137
- Audio EQ 138
- Audio Delays 139
- Automation Inputs/Outputs 139
- Management 139
- Power Requirements 139
- Hardware Dimensions 139
- Regulatory Compliance 140
- E&OE 140
© 2020, manymanuals.com. All rights reserved. | 0.708 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals